Purchase All Railyard Safety Products Online
6” D2000 Style 10 Stainless Steel Swivel Joint with Standard Bearings. Grease Type: Standard - Dura-Lith Inlet Connection: Stainless Steel 300# Flange Outlet Connection: Stainless Steel 300# Flange Buna Seals.

D2106SLS6S6SB Swivel Joints - Style 10

6” D2000 Style 10 Stainless Steel Swivel Joint with Standard Bearings. Grease Type: Standard - Dura-Lith Inlet Connection: Stainless Steel 300# Flange Outlet Connection: Stainless Steel 300# Flange Buna Seals.

$29,077.00 Each

6” D2000 Style 10 Stainless Steel Swivel Joint with Standard Bearings. Grease Type: Standard - Dura-Lith Inlet Connection: Stainless Steel 300# Flange Outlet Connection: Stainless Steel 300# Flange Viton Seals.

D2106SLS6S6SV Swivel Joints - Style 10

6” D2000 Style 10 Stainless Steel Swivel Joint with Standard Bearings. Grease Type: Standard - Dura-Lith Inlet Connection: Stainless Steel 300# Flange Outlet Connection: Stainless Steel 300# Flange Viton Seals.

$29,077.00 Each

Mobile Loading Platform Front Stabalizing Jack - Caster End

19-3654 Mobile Loading Platform

Mobile Loading Platform Front Stabalizing Jack - Caster End

$206.00 Each

Mobile Loading Platform Front Stabalizing Jack - Caster End

19-3654 Mobile Loading Platform

Mobile Loading Platform Front Stabalizing Jack - Caster End

$206.00 Each

Mobile Loading Platform Rear Stabalizing Jack - Stair End

19-3655 Mobile Loading Platform

Mobile Loading Platform Rear Stabalizing Jack - Stair End

$302.00 Each

Mobile Loading Platform Rear Stabalizing Jack - Stair End

19-3655 Mobile Loading Platform

Mobile Loading Platform Rear Stabalizing Jack - Stair End

$302.00 Each

4" D2000, Style 20, carbon steel, ANSI B16.5 150# flanged ends, H block Viton seal

D2204C1C22CSV Swivel Joints - Style 20

4" D2000, Style 20, carbon steel, ANSI B16.5 150# flanged ends, H block Viton seal

$1,104.00 Each

Telescope Jack - Height Range: 39" - 51" - Load Bearing Capacity: 25,000lbs - Top: 7" - Base: 12" - Weight 35lbs Raise and lower in 1-1/2" increments with 2-pin locking handle NOTE: Use wood blocking to fill up daylight between top of jack and trailer

4013-08 Truck Trailer Stabilizing Jacks

Telescope Jack - Height Range: 39" - 51" - Load Bearing Capacity: 25,000lbs - Top: 7" - Base: 12" - Weight 35lbs Raise and lower in 1-1/2" increments with 2-pin locking handle NOTE: Use wood blocking to fill up daylight between top of jack and trailer

$323.00 Each

Standard Jack - without wheels - Height Range: 43-1/2" - 50-1/2" - Load Bearing Capacity: 25,000lbs - Top: 5" - Base: 12" - Weight 44lbs Screw Diameter: 1-1/2" No Zerk Fitting Top plate does not tilt

4013-05 Truck Trailer Stabilizing Jacks

Standard Jack - without wheels - Height Range: 43-1/2" - 50-1/2" - Load Bearing Capacity: 25,000lbs - Top: 5" - Base: 12" - Weight 44lbs Screw Diameter: 1-1/2" No Zerk Fitting Top plate does not tilt

$284.00 Each

Solar Powered flashing blue light. Shock-proof and weather-tight. Gravity switch activates light when sign holder is at 45 degree angle or greater. Brilliant 6-LED light visible for over a mile. Mounting bracket provided.

4115-135 Derails - Accessories

Solar Powered flashing blue light. Shock-proof and weather-tight. Gravity switch activates light when sign holder is at 45 degree angle or greater. Brilliant 6-LED light visible for over a mile. Mounting bracket provided.

$324.00 Each

Non-Slide Wheel Contact Crane Stop Use wherever below rail head clearance is minimal and where a non-sliding crane stop is needed. Wedge dogs lock wedge to rail head and do not interfere with hook bolts. On impact, stops slide only marginally or not at al

4016-20 Crane Stops

Non-Slide Wheel Contact Crane Stop Use wherever below rail head clearance is minimal and where a non-sliding crane stop is needed. Wedge dogs lock wedge to rail head and do not interfere with hook bolts. On impact, stops slide only marginally or not at al

$1,935.00 Each

Uses the cushioning capacity of the tie and a wheel-bump feature to lift the wheel slightly off the rail to absorb momentum of moving car. Recommended for industrial spur tracks which do not require a bumping post but which need more protection.

4016-06 Rail Car Stops

Uses the cushioning capacity of the tie and a wheel-bump feature to lift the wheel slightly off the rail to absorb momentum of moving car. Recommended for industrial spur tracks which do not require a bumping post but which need more protection.

$1,348.00 Each

Non-Slide Bumper Crane Stop Wedge stands 15 inches above top of rail. Underside of crane bumper should not be more than 12" above top of rail. Specify rail size and section.

4016-21 Crane Stops

Non-Slide Bumper Crane Stop Wedge stands 15 inches above top of rail. Underside of crane bumper should not be more than 12" above top of rail. Specify rail size and section.

$1,699.00 Each

Cushion-Slide Bumper Contact Crane Stop Wedge stands 15” above top of rail. All standard crane bumper heights can be accommodated. Cinch plates are made to fit a specific rail size and section.

4016-08 Crane Stops

Cushion-Slide Bumper Contact Crane Stop Wedge stands 15” above top of rail. All standard crane bumper heights can be accommodated. Cinch plates are made to fit a specific rail size and section.

$1,583.00 Each

Cushion Slide Wheel Crane Stops Wedges made to fit a specific wheel diameter. Wedges meet OSHA regulation that half the wheel diameter is covered. Cinch plates are made for a specific rail size and section.

4016-07 Crane Stops

Cushion Slide Wheel Crane Stops Wedges made to fit a specific wheel diameter. Wedges meet OSHA regulation that half the wheel diameter is covered. Cinch plates are made for a specific rail size and section.

$1,467.00 Each

Single Flush Rail Wheel Chock with Flag Weight 16lbs

4011-33 Wheel Chocks - Whack Em

Single Flush Rail Wheel Chock with Flag Weight 16lbs

$163.00 Each

Ready to use shim plates, 1/4" thick, ensure a proper height adjustment and a secure mounting of hinged derails with manual lift sign holders.

4014-31 Derails - Accessories

Ready to use shim plates, 1/4" thick, ensure a proper height adjustment and a secure mounting of hinged derails with manual lift sign holders.

$20.00 Each

Ready to use shim plates, 1/4" thick, ensure a proper height adjustment and a secure mounting of hinged derails with manual lift sign holders.

4014-32 Derails - Accessories

Ready to use shim plates, 1/4" thick, ensure a proper height adjustment and a secure mounting of hinged derails with manual lift sign holders.

$24.00 Each

2-Way Hinged Derail (for Locomotive) with manual sign holder suitable for 6-axle and 4-axle locomotives and all freight cars. Low-angle deflection bar accommodates longer wheel base of 6-axle locomotives. Allow ample space alongside the track for derail

4014-18 Derails - Hinged

2-Way Hinged Derail (for Locomotive) with manual sign holder suitable for 6-axle and 4-axle locomotives and all freight cars. Low-angle deflection bar accommodates longer wheel base of 6-axle locomotives. Allow ample space alongside the track for derail

$1,796.00 Each

Locomotive Chocking Skid (Exposed Rail) At 16 lbs and 17½ " long, this model skid is handy for chocking locomotive on flat track. The low-profile (4" tall) handle clears any wheel frame or brake shoe obstruction.

4016-13 Rail Skids

Locomotive Chocking Skid (Exposed Rail) At 16 lbs and 17½ " long, this model skid is handy for chocking locomotive on flat track. The low-profile (4" tall) handle clears any wheel frame or brake shoe obstruction.

$219.00 Each

Aldon® Adjustable Height Trailer Stabilizer Steel Adjustable height 42” - 46” 75,000 lbs. proven load capacity

4013-13 Truck Trailer Stabilizing Jacks

Aldon® Adjustable Height Trailer Stabilizer Steel Adjustable height 42” - 46” 75,000 lbs. proven load capacity

$675.00 Each

Safety Products
BEST SELLER
DR-1 One Way Right Throw One-Way Hinged FOR FREIGHT CARS and LOCOMOTIVES For rails 60 lbs. and heavier. Derails are sized to fit a specific rail height, including thickness of tie plate. Weight 156 lbs.

4014-02 Derails - Hinged

DR-1 One Way Right Throw One-Way Hinged FOR FREIGHT CARS and LOCOMOTIVES For rails 60 lbs. and heavier. Derails are sized to fit a specific rail height, including thickness of tie plate. Weight 156 lbs.

$1,228.00 Each

6” D2000 Style 50 Carbon Steel Swivel Joint with Standard Bearings. Grease Type: Standard - Dura-Lith Inlet Connection: Carbon Steel Buttweld Outlet Connection: Carbon Steel Buttweld No Seals.

D2506CLC1C1SN Swivel Joints - Style 50

6” D2000 Style 50 Carbon Steel Swivel Joint with Standard Bearings. Grease Type: Standard - Dura-Lith Inlet Connection: Carbon Steel Buttweld Outlet Connection: Carbon Steel Buttweld No Seals.

$7,656.00 Each

CS-2 Self-Tightening Car Stop Car Stop is assembled on head of rail by tightening 5 bolts and driving wedge from the rear. Weight 107lbs

4016-03 Rail Car Stops

CS-2 Self-Tightening Car Stop Car Stop is assembled on head of rail by tightening 5 bolts and driving wedge from the rear. Weight 107lbs

$548.00 Each